UbiBot
Soil PH (3-9 PH) Sensor Probe with 1.9m cable
for UbiBot GS1-AETH1RS / GS1-AL4G1RS / SP1
(Model No.: UBISPH3M)
Monitoring the soil PH with wide range and good linearity
Descriptions
This probe specialises in monitoring PH of soil. Embedded with industrial-grade chip, the probe offers accurate measurement. The stainless steel probe can be inserted into the soil for a long term without being corroded. The durable cable ensures stable data transmission.
The Audio plug is designed for the UbiBot GS1 device.
The measurements are transferred to the devices, displayed on the large LCD screen and synced to the platform via network. So you can access the data instantly on the screen or remotely view them via our app or web console.
Features
- Electrolysis-resistant
- Design to pairs UbiBot GS1 device
- Accurate, fast data acquistion
- Stainless steel probe
Application Instructions
For once use only:
Insert the steel probe point vertically to the soil at your preferred depth. Hold the probe tightly in case of it shaking. Avoid touching stones or any other hard objects, because that will damage the probe. Please wait for about 20 minutes to allow the sensor to work properly.
For long time berried in soil:
Dig a hole at over 20cm-diameter on the ground or soil in your greenhouse. Insert the steel probe point in horizontal direction to the soil. Leave the probe in the soil and you can have your data remotely.
Applications
- Geological Survey
- Horticulture PH Monitoring
- Succulent Plant Caring
- Green House Soil Condition Management
Specification:
- Power supply: DC 5-30V
- Maximum power consumption: 0.5W (24V DC power supply)
- Measuring range: 3-9 PH
- Measuring Accuracy: ±0.3PH
- Operating temperature: -20℃~60℃
- Protection: IP68
- Cable Length: 1.9m
- Response time: ≤10s
- Dimension: 45*15*123mm
- Output signal: RS485 (Modbus protocol)
- Firmware V1.1.1 or above
Special Note: ONLY support UniBot GS1/GS1-S series produced after 18 July 2022. GS1-1DS is not supported.
UbiBot
Soil PH (3-9 PH) Sensor Probe with 1.9m cable
for UbiBot GS1-AETH1RS / GS1-AL4G1RS / SP1
(Model No.: UBISPH3M)
Monitoring the soil PH with wide range and good linearity
Descriptions
This probe specialises in monitoring PH of soil. Embedded with industrial-grade chip, the probe offers accurate measurement. The stainless steel probe can be inserted into the soil for a long term without being corroded. The durable cable ensures stable data transmission.
The Audio plug is designed for the UbiBot GS1 device.
The measurements are transferred to the devices, displayed on the large LCD screen and synced to the platform via network. So you can access the data instantly on the screen or remotely view them via our app or web console.
Features
- Electrolysis-resistant
- Design to pairs UbiBot GS1 device
- Accurate, fast data acquistion
- Stainless steel probe
Application Instructions
For once use only:
Insert the steel probe point vertically to the soil at your preferred depth. Hold the probe tightly in case of it shaking. Avoid touching stones or any other hard objects, because that will damage the probe. Please wait for about 20 minutes to allow the sensor to work properly.
For long time berried in soil:
Dig a hole at over 20cm-diameter on the ground or soil in your greenhouse. Insert the steel probe point in horizontal direction to the soil. Leave the probe in the soil and you can have your data remotely.
Applications
- Geological Survey
- Horticulture PH Monitoring
- Succulent Plant Caring
- Green House Soil Condition Management
Specification:
- Power supply: DC 5-30V
- Maximum power consumption: 0.5W (24V DC power supply)
- Measuring range: 3-9 PH
- Measuring Accuracy: ±0.3PH
- Operating temperature: -20℃~60℃
- Protection: IP68
- Cable Length: 1.9m
- Response time: ≤10s
- Dimension: 45*15*123mm
- Output signal: RS485 (Modbus protocol)
- Firmware V1.1.1 or above
Special Note: ONLY support UniBot GS1/GS1-S series produced after 18 July 2022. GS1-1DS is not supported.
